Manual and instructions Slope Ceiling Mount
The Lupit Pole Slope Ceiling Mount can only be used for Lupit Pole Classic and Diamond G2 poles
Use the Lupit Pole Classic / Diamond installation manual and Slope Ceiling Mount installation video for proper installation.
Before drilling:
- Make sure that there are no electrical cables, water pipes or gas pipes or other dangerous obstacles where you are going to drill
- Only install the Lupit Pole Slope Ceiling Mount on a concrete ceiling:
If your ceiling is made of other material, or you have a plaster ceiling, the construction must be checked by an expert and, if necessary, additionally be reinforced before you can install this fixing
- ALL FOUR holes must be used to attach the Slope Ceiling Mount
- To calculate whether this Slope Ceiling Mount fits under your ceiling together with the basic set, or if you need an extension tube, you must measure the following distance:
1) measure the vertical distance from the middle point of the Slope Ceiling Mount to the floor
2) Reduce the distance measured at 1) by 50-60mm
3) use that reduced measure in the Lupit Pole-height calculator to calculate whether the basic set is sufficient, or whether you need an extension tube for correct installation.
Use the Lupit Pole Classic / Diamond installation manual and Slope Ceiling Mount installation video for proper installation.
- Be extra careful when tightening the post between the floor and the wall:
Make sure the pole is not over-tightened, otherwise damage to the ceiling may occur or it can loosen the Slope Ceiling Mount.
- Check the stability of the pole before each use by giving it a good, hard shake.
Watch the instructional video for attaching the Slope Ceiling Mount and the installation of the Classic/Diamond poles
Collapsible content
General information
I import most items especially for you from the USA, Poland or Slovenia. The average delivery time is 1 to 1½ weeks (within the Netherlands) but this can also be longer. This is an average delivery time, therefore it's not a promise or guarantee! Please keep that in mind!
Please note:
*When returning multiple items that have been purchased for you, I always calculate the costs incurred per individual situation. The amount that is deducted and what is converted into shop credit therefore depends on the actual costs that have been incurred and concerns a reasonable compensation for the losses suffered **The charges only cover the costs incurred in purchasing and importing the items from America; no standard cancellation fees or restocking fees that cannot be substantiated or explained will be charged. More about the reasonable compensation can be found in this Dutch text here en hereThis applies to: |
I would prefer not to have to charge these costs, but in order to cover the costs (losses) I have incurred due to the increasing number of returns, this has unfortunately proven necessary. To limit the number of returns (please think about the environment too) I would like to ask you to think just a little longer about your purchase, to make a well-considered decision and, if you are unsure, to ask me for advice or help!
For a single exchange for a different size, these costs will not be charged. You can read more about this in the Terms and Conditions and Refund Policy.
Contact
Email:
info@party-shoes.nl
Visiting address:
On appointment Only (Monday - Friday)!
Kinky- & Party-shoes
Thomas J. Witteroosstraat 18
6827 AZ ARNHEM (NL)
KvK 743 520 16 | BTW-id NL 002 366 589 B32
Sizing and Dimensions
See how you can calculate your size using a conversion table on our information page: "How do I know which size I have and which one I should order?"
To view a conversion table and see which sizes & dimensions we use, you can use the size chart, which you can find in the following two ways:
On every page (both on your mobile and on a computer) you can find a button for a size chart on the right side, which looks like this:
On all product pages you can find the button for the table above the "Add to cart" button, which looks like this:
Our shoes and boots come from the USA and have American sizes (1 inch = 2.54 cm).
These dimensions have been converted to the Western European size that we use in the Netherlands, Belgium and other EU countries. Our converted EU dimensions differ from those of our American supplier stated on the box. Experience shows that shoe sizes US-12 and up in particular are larger.
Order the size you normally wear, we already take into account how a model fits (large, small or according to size). Sometimes we explicitly inform you about this in the description.
If you are between sizes, we usually recommend rounding up the size for a closed model, such as a pump or boot. With an open model, such as a sandal or peep toes (where the toes and heel are 'open') we recommend to choose the smaller size.
If you want to order a specific US size, please select the desired US size indicated in the sizes. We always order the corresponding US size stated; the corresponding EU size determined by us may therefore differ from the EU size stated on the box.
Of course you can always ask us for advice about which size you need: info@kinky-shoes.nl
If you would like to know the shaft circumference, shaft height and calf circumference of boots, you can calculate these for your size (for an explanation of how to do this; view our information page about calculating the circumference). Use the following data sheet for this:
The Boot calf/shaft size data sheet